MASTERING PLUMBING FUNDAMENTALS FOR INSTALLING A BATHTUB

Mastering Plumbing Fundamentals for Installing a Bathtub

Mastering Plumbing Fundamentals for Installing a Bathtub

Blog Article

Call

Each person seems to have their own individual thoughts about How to Install a Bathtub.


A Step-by-Step Guide to Installing a Bathtub
Mounting a tub isn't precisely brain surgery, but it does require solid plumbing, carpentry, and also in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard project. If the old bathtub is conveniently obtainable, the project can move rapidly; if you have to open up a wall to get rid of the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to vacate the old tub and set in the new one. Make certain you have actually certified yourself for the task as well as fit attempting it. Instead of hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one before you begin. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly help you install a new bathtub in your shower room if you have already gotten a new tub as well as do not require to alter the plan of your previous water pipes.
Your tools as well as material list ought to make up the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Preparing for the Installation


    To start with, the supporting framework provided with the bathroom ought to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to prevent stress on the bathtub.
    Fit the versatile faucet ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the provided washers.
    Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.

    Removing Old Touches


    If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted accessibility that is typically the instance.
    Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will originate from the pipes. When the supply pipes have actually been eliminated, use the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this procedure. When the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
    Before going on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Tub


    Utilizing the two wooden boards under its feet, place the tub in the required placement. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
    The following objective is to guarantee that the tub is leveled all round. This can be accomplished by checking the level and changing the feet on the tub up until the level reads degree.
    To set up faucets, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
    Switch on the water supply and inspect all joints and also new pipework for leakages as well as tighten them if required. Fill the bathtub as well as also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Finally, fix the bath paneling as described in the producer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the tub has actually been made use of at least when as this will settle it into its final position.

    Suitable New Touches


    If the tails of the new faucets are plastic, then you will certainly need a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end provides a connection to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly need lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in area between the faucet as well as the sink. Safeguard the tap in position with the maker supplied backnut. Once the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind must be connected to the tap ends first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the location where the bath meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to split an inflexible seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with moisture and feasible leakages to the ceiling below.
    You can pick from a variety of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealant can break relatively very early if you do not consider this activity prior to sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the market. It is recommended to fit the ceramic tiles using water-resistant or water resistant sticky as well as grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Installing A Bathtub

    Do you really like reading about A Step-by-Step Guide to Installing a Bathtub? Make feedback down the page. We would be interested to see your views about this blog entry. Hoping that you visit us again soon. Sharing is good. Helping others is fun. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .


    Leading plumbing expertise for emergencies.

    Report this page